An Easy Instruction for Installing a Bathtub
An Easy Instruction for Installing a Bathtub
Blog Article
How do you feel when it comes to How to Install a Bathtub?
Setting up a tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, as well as often, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately challenging project. If the old bathtub is readily available, the project can relocate immediately; if you need to open a wall surface to remove the old tub and place the new bath tub, the task is a lot harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to vacate the old tub and also embeded in the new one. See to it you have qualified yourself for the job and fit trying it. Rather than hiring a contractor to take control of a halfway-completed job, it is much better to consider utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube links.
This write-up will certainly help you set up a brand-new tub in your bathroom if you have currently acquired a brand-new bathtub and don't need to alter the setup of your previous water pipelines.
Your devices and also product list need to make up the following:
Getting ready for the Installation
To start with, the supporting frame supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets system to prevent stress on the tub.
Fit the flexible tap adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the limited gain access to that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Before moving on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Making use of the two wood boards under its feet, position the tub in the required position. The wood boards are handy in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bathtub up until the level reads level.
To mount taps, fit the bottom of the furthest adaptable faucet port to the appropriate supply pipe by making a compression join; then do the same for the other faucet.
Activate the water supply and examine all joints and also new pipework for leaks and also tighten them if essential. Load the bathtub as well as likewise check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the tub should wait till the tub has actually been utilized at least when as this will settle it right into its final placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin ensuring that the washers are in place in between the faucet and also the sink. Protect the tap in place with the supplier given backnut. When the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The former kind must be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface between the bathroom and the tiling, resulting in issues with moisture and possible leakages to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes and also cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water prior to securing, to permit the motion experienced when the tub is in use. The sealer can break fairly very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very excited about Installing A Bathtub and I really hope you appreciated our blog post. You should take the time to share this content if you enjoyed reading it. We cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Emergency? Call us! Report this page